非柔性连接石化储罐配管温差应力分析与对策

储罐配管在温差作用下产生热位移会导致管壁产生热应力，未采用柔性连接的配管由于热应力集中作用可能发生破漏。针对与石油化工储罐非柔性连接的配管的安全问题，应用ANSYS有限元分析软件模拟计算石化企业典型配管的热应力分布；根据不同类型配管的分析结果，提出了工程技术与管理方面的针对性安全措施。研究结果表明:温差效应对石化储罐配管热应力影响显著，随内外温差的增加，配管应力集中的区域增大，最大热应力值增大；补偿措施能够改善配管的柔性，降低配管应力；约束载荷限制配管热膨胀从而增大配管应力；三通管是多根配管接合的区域，这种复杂管道交汇处会形成明显应力集中。研究结果对于提高石油化工非柔性连接配管安全性有一定的指导意义。     

Evaluation of photolysis and hydrolysis of pyraclostrobin in aqueous solutions and its degradation products in paddy water

This study evaluated the hydrolysis and photolysis kinetics of pyraclostrobin in an aqueous solution using ultra-high-performance liquid chromatography–photodiode array detection and identified the resulting metabolites of pyraclostrobin by hydrolysis and photolysis in paddy water using high-resolution mass spectrometry coupled with liquid chromatography. The effect of solution pH, metal ions and surfactants on the hydrolysis of pyraclostrobin was explored. The hydrolysis half-lives of pyraclostrobin were 23.1–115.5?days and were stable in buffer solution at pH 5.0. The degradation rate of pyraclostrobin in an aqueous solution under sunlight was slower than that under UV photolysis reaction. The half-lives of pyraclostrobin in a buffer solution at pH 5.0, 7.0, 9.0 and in paddy water were less than 12?h under the two light irradiation types. The metabolites of the two processes were identified and compared to further understand the mechanisms underlying hydrolysis and photolysis of pyraclostrobin in natural water. The extracted ions obtained from paddy water were automatically annotated by Compound Discoverer software with manual confirmation of their fragments. Two metabolites were detected and identified in the pyraclostrobin hydrolysis, whereas three metabolites were detected and identified in the photolysis in paddy water.     

简述排污许可制下火电行业现状及发展

实施排污许可制度,是强化排污者责任、提高固定污染源环境管理效能、改善环境质量的重要制度保障。火电行业作为典型的高架固定源,先行试点实施排污许可制度。通过分析火电行业发展和环保现状,结合排污许可管理要点,简述排污许可制对火电行业发展的影响。     

The Thermal Discharges From Nuclear Power Plants in Taiwan

The increasing use of sea water for industrial cooling presents a real threat to the ecological environment in the ocean. in Taiwan where many electric power plants along the coast take sea water for cooling, people are concerned seriously about nuclear power plants. There are three nuclear power plants in Taiwan. Each plant has two units for generating power. the first two are located along the northern coast of Taiwan. the third is located in Kenting National Park along the coast of southernmost Taiwan. the plants take sea water for cooling, and discharge their heated effluents to the ocean surface from the coast. the thermal effluents have variable effects on the ecological environment near the plants. Fishermen living near the power plants complain that the heated water affects the inshore fishery catch. in addition, the thermal water from the second plant is easily accumulated near the coastal zone to influence the nearby swimming area in the summer-time. the thermal water from the third plant bleaches or kills some corals in shallow water near the outlet, and this conflicts with the interests of Kenting National Park.     

焦化废水处理过程中固相物质的形成及处置方法评价

焦化废水处理过程中产生的焦油、污泥和结晶杂盐等固相物质,既有资源属性,又有污染特性,但目前缺乏基于能源、经济及环境影响方面的评估.本研究阐述了3类固相物质的形成机制,建立了质量当量计算及处置方法评价模型.以宝武集团韶关钢铁股份有限公司焦化厂（二期）焦化废水处理工程的A/O/H/O（厌氧/好氧/水解/好氧）流化床工艺作为考察对象,利用工程运行参数和水质统计数据进行固相物质的产量推算,结果发现,焦油、物化污泥、生物污泥（含水率为80%）和工业杂盐的产率分别为0.186、5.80、4.24和1.97 kg·m^-3.通过处置方法评价模型明确了焦油焚烧、污泥热解、结晶杂盐分盐提纯后工业应用是最佳处置方案,在60 m³·h^-1废水处理规模的固相物质处置过程中,每年约产生1177 MWh的能源,获得135.0万元的经济效益,排放627.0 t CO₂,表明能源回收、经济效益和环境影响的协同存在.     

铝系混凝剂优势形态分析及其混凝特性

聚合氯化铝（PACl）是常用的水处理混凝剂,在应用过程中通常表现出比传统铝盐更为优异的效果.研究表明,这种优异性能主要得益于其特殊的组成,特别是高分子聚合物Al₁₃和Al₃₀独特的物化特性.Al₁₃和Al₃₀是铝离子水解过程中的中间产物,在地球科学和环境化学等领域有着重要的研究价值.于水处理而言,二者的结构和分子特性是研究者关注的重点,大量研究基于此展开,很多重要的发现为实际应用奠定了基础.基于对PACl及其组成性质的研究,本文对PACl的混凝特性及其优势形态分子的分析进行了综合阐述.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

石英灯辐射加热条件下低密度碳/酚醛复合材料高温响应及分析

目的研究低密度碳/酚醛复合材料在不同地面加热实验测试响应的差异性,指导材料在实际应用环境下的高温响应分析。方法对低密度碳/酚醛复合材料开展了热流为400 kW/m~2的单侧石英灯辐射加热实验,利用热电偶测温系统测量试件在加热过程中不同位置的温度时间历程,并对试件的烧蚀形貌和微观结构进行观测。同时与热流为464k W/m~2的氧乙炔加热陶瓷板辐射加热实验结果进行对比分析,并且采用有限元方法对材料的传热传质多场耦合计算进行分析。结果对于石英灯辐射加热,在测量点升温到接近200℃时,温度响应拐点都依次出现。由于加热的辐射热源不同,在不同的辐射波段下,多孔材料吸收和发射的热量不同,短时间内氧乙炔加热陶瓷板辐射加热使材料内部升温速率比石英灯辐射加热实验的要快,但长时间加热时现象刚好相反。结论进行传热传质多场耦合计算材料高温响应时,合理确定材料宏观性能随温度的变化至关重要。     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

包装箱用碳纤维增强复合材料贮存寿命研究

目的研究碳纤维增强复合材料贮存条件下的性能变化趋势和寿命评估。方法对碳纤维增强复合材料开展四个不同温度条件下的热氧老化试验,按试验周期定期取样开展冲击性能测试,对试验数据采用寿命预估方法进行处理,对材料性能进行预估。结果通过数据计算分别得到我国热带海洋、干热沙漠等典型气候条件下的碳纤维增强复合材料贮存寿命分别为17.21~35.89年。结论碳纤维增强复合材料具有较好的贮存性能,在较为严酷的热带海洋气候和给定的失效判据条件下,寿命预计为17.21年。试验和数据处理方法可以较好地预计材料的性能变化趋势和开展寿命评估。